✨ feat:新板子变更引脚

YueJin_test_bench/source/Appliciation/Check_Ctrl.c

@@ -326,7 +326,7 @@ uint8_t yibiaoshuju[34];
             
 
         default:            
-            POWER_CTRL_KL30   = 0u;
+            // POWER_CTRL_KL30   = 0u;
             POWER_CTRL_KL15   = 0u;
             CAN_Msg_Tx_Enable = 1u;
             Display_Menu_Type = 0;
@@ -613,7 +613,7 @@ void Function_Check_Ctrl(uint32_t cmd)
                 {
 
                 }
-
+                // ONE_START = 1;
                 
                 break;
             }
@@ -645,26 +645,26 @@ void Function_Check_Ctrl(uint32_t cmd)
                 if(ONE_KEY_ONOFF <= 20)
                 {
                     RELAY_KEY_MCU = 1;
-                    ONE_START = 0;
+                    ONE_START = 1;
                 }
                 else if(ONE_KEY_ONOFF <= 40)
                 {
                     RELAY_KEY_MCU = 0;
-                    ONE_START = 1; 
+                    ONE_START = 0; 
                 }
                 else if(ONE_KEY_ONOFF <= 60)
                 {
                     RELAY_KEY_MCU = 0;
-                    ONE_START = 0;
+                    ONE_START = 1;
                 }
                 else if(ONE_KEY_ONOFF <=70)
                 {
                     RELAY_KEY_MCU = 0;
-                    ONE_START = 1;
+                    ONE_START = 0;
                 }
                 else if(ONE_KEY_ONOFF>110 && ONE_KEY_ONOFF <=120)
                 {
-                    ONE_START = 0;
+                    ONE_START = 1;
                     ABC_OUT = 1;
                 }  
                 else
@@ -678,7 +678,7 @@ void Function_Check_Ctrl(uint32_t cmd)
                 RELAY_VBAT_MCU = 1;
                 RELAY_DC12V_MCU = 1;
                 RELAY_KEY_MCU = 1;
-                ONE_START = 0;
+                ONE_START = 1;
                 FULL_BEAM = 0;
                 break;
             }            
@@ -735,23 +735,23 @@ void Function_Check_Ctrl(uint32_t cmd)
                 RELAY_LIGHTCONTROL_MCU = 0;
                 if(ACCONOFF_delay_3s <= 5)
                 {
-                    ONE_START = 0;
+                    ONE_START = 1;
                 }
                 else if(ACCONOFF_delay_3s > 5 && ACCONOFF_delay_3s <= 8)
                 {
-                    ONE_START = 1;
+                    ONE_START = 0;
                 }
                 else if(ACCONOFF_delay_3s > 10 && ACCONOFF_delay_3s <= 13)
                 {
-                    ONE_START = 0;
+                    ONE_START = 1;
                 }
                 else if(ACCONOFF_delay_3s > 13 && ACCONOFF_delay_3s <= 17)
                 {
-                    ONE_START = 1;
+                    ONE_START = 0;
                 }
                 else 
                 {
-                    ONE_START = 0;
+                    ONE_START = 1;
                 }
 
                 if(ACCONOFF_delay_3s > 17 && CHECK_Value == 0)

YueJin_test_bench/source/Appliciation/RTE_GPIO.c

@@ -173,6 +173,12 @@ void RTE_GPIO_Init(void)
     gpio_temp.enGPIODir    = GPIO_DIR_OUT;
     gpio_temp.enGPIOAltFun = GPIO_ALTER_FUN_1;
     GPIO_Config(&gpio_temp);
+    gpio_temp.enGPIOPort   = GPIO_PORT_GROUP_0;
+    gpio_temp.enGPIOPIN    = GPIO_PIN_4;
+    gpio_temp.enGPIOMode   = GPIO_MODE_PORT;
+    gpio_temp.enGPIODir    = GPIO_DIR_OUT;
+    gpio_temp.enGPIOAltFun = GPIO_ALTER_FUN_1;
+    GPIO_Config(&gpio_temp);
     // queren =  0;
     // LINE_OUT_NEG_01 = 1;
     // LINE_OUT_NEG_02 = 1;

YueJin_test_bench/source/Appliciation/RTE_GPIO.h

@@ -7,8 +7,8 @@
 
 #define LINE_OUT_NEG_09 GPIO_OUT_PORT10_PIN04 //485_RE
 
-#define ONE_START GPIO_OUT_PORT10_PIN14   //一键启动
-#define ABC_OUT GPIO_OUT_PORT10_PIN13   //ABC轮动报警输出
+#define ONE_START GPIO_OUT_PORT10_PIN13   //一键启动
+#define ABC_OUT GPIO_OUT_PORT00_PIN04   //ABC轮动报警输出
 
 #define RELAY_VBAT_MCU GPIO_OUT_PORT10_PIN10 
 #define RELAY_DC12V_MCU GPIO_OUT_PORT10_PIN09
@@ -45,7 +45,7 @@
 
 
 /*  ---------------------旧的-------------------------- */
-#define POWER_CTRL_KL30         GPIO_OUT_PORT10_PIN13
+// #define POWER_CTRL_KL30         GPIO_OUT_PORT10_PIN13
 #define POWER_CTRL_KL15         GPIO_OUT_PORT10_PIN12
 #define SW10 GPIO_IN_PORT10_PIN02
 #define LINE_OUT_NEG_01 GPIO_OUT_PORT09_PIN06   //12V

YueJin_test_bench/source/Appliciation/app_lsdn.c

@@ -14,7 +14,7 @@ void set_pin_high(uint8_t mode)
     }
     else
     {
-        ONE_START = 0;
+        ONE_START = 1;
     }
 }
 void set_pin_low(uint8_t mode)
@@ -28,7 +28,7 @@ void set_pin_low(uint8_t mode)
     }
     else
     {
-        ONE_START = 1;
+        ONE_START = 0;
     }
 }
 void lsdn_delay_us(uint32_t us)

YueJin_test_bench/source/System/init.c

@@ -77,7 +77,8 @@ void Sys_Startup_Init(void)
     // GPIO_DIR_PORT00_PIN08 = 1;
     // TX_OUT = 0;
 
-    ONE_START = 0;
+    ONE_START = 1;
+    ABC_OUT = 0;
 
     GPIO_SET_KEPP( );
     RTE_ADC_Init( );
@@ -110,7 +111,7 @@ void Sys_Startup_Init(void)
     loc_config.pfnUARTConfirmCallBack = 0;
     loc_config.pfnUARTErrHandleCallBack = 0;
     loc_config.pfnUARTReadMsgCallBack = UART_Put1;
-    UART_Init(UART_RLIN31, &loc_config);
+    // UART_Init(UART_RLIN31, &loc_config);
     // Auto_ONOFF = 1;
     // AutoFlag = 1;
 }

YueJin_test_bench/utility/GPIO/GPIO.c

@@ -48,7 +48,7 @@ const uint16_t g_u16GPIOConfigArray[56U][2U] =
     {0x0000u, 0x0000u},
     {0x0630u, 0x0600u},
     {0x0220u, 0x2207u},
-    {0x79CFu, 0x79FFu},
+    {0x79DFu, 0x79FFu},
     {0x0000u, 0x0000u},
     {0x0000u, 0x0000u},
     {0x0000u, 0x0000u},

YueJin_test_bench/utility/诊断工具1.10.11 x64/Option/GPIO_RH850_F1KM_CFG.json

@@ -198,7 +198,7 @@
           "pinName": "Pin_P0_04",
           "pinAddress": "11",
           "wakeupPin": {
-            "PinModeName": "CAN2TX",
+            "PinModeName": "GPIO_OUT",
             "PUn": false,
             "PDn": false,
             "PISn": false,
@@ -207,9 +207,9 @@
             "PFCAEn": false,
             "PIPCn": false,
             "Pn": false,
-            "PMCn": true,
+            "PMCn": false,
             "PMn": false,
-            "PIBCn": false
+            "PIBCn": true
           },
           "sleepPin": {
             "PinModeName": "GPIO_OUT",

YueJin_test_bench/utility/诊断工具1.10.11 x64/Option/Option.properties

 #new Option
-#Wed Feb 19 15:12:14 CST 2025
+#Fri Mar 21 11:10:29 CST 2025
 IsSort=true
 MergeFlashIsCompression=false
 ChangeAppFilePath=
@@ -10,7 +10,7 @@ MergeCrcTtpe=1
 MergeBootFilePath=
 IsMergeChangeAddress=false
 MergeFlashOutPutFilePath=D\:\\Code\\\u7231\u739B\u68C0\u6D4B\u53F0\\\u56FE\u7247
-GPIOOutPutPath=
+GPIOOutPutPath=C\:\\Users\\Lenovo\\Desktop
 MergeCanDBCPath=
 IsFilling=true
 RxID=729