#include "Popups.h"
#include "Common_Interface.h"
#include "GUI.h"
#include "Sound_Scheduler.h"

#include "Gauges.h"
#include "GaugesInterface.h"

#include "CAN_Communication_Matrix.h"
#include "Popup_List.h"
#include "Telltales.h"

#include "Data_Gear.h"
#include "Line_in.h"

#include "Data_CoolantTemperature.h"
#include "Data_Voltmeter.h"
#include "Data_Fuel_User.h"

uint8_t PopupSeatBeltDrReq;
uint8_t PopupSeatBeltPaReq;
uint8_t PopupESCStatBackup;

GUIRadarFlashCtrlStruct GUIRADARSysFailureFlash;

uint16_t  StartupAnimationTimer;
void      GUI_RADAR_Sys_Failure_Flash_Reset(void);
void      GUI_RADAR_Sys_Failure_Flash_Reset(void)
{
    if ( GUIRADARSysFailureFlash.Cnt == 0xFF )
    {
        GUIRADARSysFailureFlash.Backup = 0;
        GUIRADARSysFailureFlash.Cnt    = 0;
    }
    else if ( GUIRADARSysFailureFlash.Cnt != 0 )
    {
        GUIRADARSysFailureFlash.Cnt = 0xFF;
    }
}


uint8_t wbytest = 0 ;
uint8_t wbyTrigger[6] ={0};
void Popups_Management_Service(void)
{
    /*    uint8_t PopupMsg = 0u;
        uint8_t PopupSnd = 0u;*/

    //Popups_Polling( );
    uint8_t i = 0 ;
    for(i = 0 ;i < POPUP_MAX ;i ++)
    {   
        if(i == wbytest )
            Popup_Request(i);
        else
            Popup_Delete(i);    
    }

    //wbytest = Popup_Get_Current_Message();

    /*    PopupMsg = Popup_Get_Current_Message();
        PopupSnd = Popup_Get_Current_Sound();

        Popups_Displaying(PopupMsg);*/
}

uint8_t Get_wbyPopupTest(void)
{
    return wbytest ;
}

void Popups_Polling(void)
{    
    uint32_t Ign_Time ;  
    uint8_t EOL = 0x00 ; 
    COMMON_PowerStatus_t    PowerSts ;
	//共用参数
    uint8_t V_Speed = 0 ;//车速
    uint8_t E_Speed = 0 ;//转速
	uint8_t variable_1 ,variable_2,variable_3,variable_4,variable_5;

    uint16_t KL30_Volt = 0 ;

    if(Get_Voltmeter_Valid())
    {
        KL30_Volt = Get_Voltmeter_AvrVoltage();
    }
    	
	if(Common_Get_IG_Sts_Valid())
    {
        Ign_Time = Common_GetIgnOnTime();
        PowerSts = Common_Get_IG_Sts();
    }
    else
    {
        Ign_Time = 0 ;
        PowerSts = COMMON_POWER_OFF ;
    }
	

    //车速有效判定
    if(Common_Get_Act_V_Speed_Valid())
    {
        V_Speed = Common_Get_Act_V_Speed();
    }
    else
    {
        V_Speed = 0 ;
    }
    //转速有效判定
    if(Common_Get_Act_E_Speed_Valid())
    {
        E_Speed = Common_Get_Act_E_Speed();
    }
    else
    {
        E_Speed = 0 ;
    }
	
	
    
    
    //0.紧急警报-刹车
    variable_1 = Get_ID_CF02F2A_Sig_Advanced_Emerg_Braking_Sys_Sta();
    variable_2 = Get_ID_CF02FA0_Sig_Advanced_Emerg_Braking_Sys_Sta();
    if(EOL == 0x01)
    {
        if(variable_1 == 7 || variable_2 == 7)
        {
            Popup_Request(POPUP1_BRAKE_BLACK);
        }
        else
        {
            Popup_Delete(POPUP1_BRAKE_BLACK);
        }
    }
    else
    {
        Popup_Delete(POPUP1_BRAKE_BLACK);
    }


    //1.紧急警报-紧急制动
    variable_1 = Get_ID_CF02FA1_Sig_Advanced_Emerg_Braking_Sys_Sta();
    if(EOL == 0x01)
    {
        if(variable_1 == 7)
        {
            Popup_Request(POPUP1_BRAKE_BRAKE);
        }
        else
        {
            Popup_Delete(POPUP1_BRAKE_BRAKE);
        }
    }
    else
    {
        Popup_Delete(POPUP1_BRAKE_BRAKE);
    }


    //2.车间距警报-刹车(红字)
    variable_1 = Get_ID_CF02F2A_Sig_Advanced_Emerg_Braking_Sys_Sta();
    variable_2 = Get_ID_CF02FA0_Sig_Advanced_Emerg_Braking_Sys_Sta();
    if(EOL == 0x01)
    {
        if(variable_1 == 6 || variable_2 == 6)
        {
            Popup_Request(POPUP1_BRAKE_SPACING_R);
        }
        else
        {
            Popup_Delete(POPUP1_BRAKE_SPACING_R);
        }
    }
    else
    {
        Popup_Delete(POPUP1_BRAKE_SPACING_R);
    }


    //3.车间距警报-碰撞报警
    variable_1 = Get_ID_CF02FA1_Sig_Advanced_Emerg_Braking_Sys_Sta();
    if(EOL == 0x01)
    {
        if(variable_1 == 6)
        {
            Popup_Request(POPUP1_BRAKE_SPACING_COLLISION	);
        }
        else
        {
            Popup_Delete(POPUP1_BRAKE_SPACING_COLLISION	);
        }
    }
    else
    {
        Popup_Delete(POPUP1_BRAKE_SPACING_COLLISION	);
    }


    //4.车间距警报-刹车(黄字)
    variable_1 = Get_ID_CF02F2A_Sig_Advanced_Emerg_Braking_Sys_Sta();
    variable_2 = Get_ID_CF02FA0_Sig_Advanced_Emerg_Braking_Sys_Sta();
    if(EOL == 0x01)
    {
        if(variable_1 == 5 || variable_2 == 5)
        {
        Popup_Request(POPUP1_BRAKE_SPACING_Y);
        }
        else
        {
            Popup_Delete(POPUP1_BRAKE_SPACING_Y);
        }
    }


    //5.ASR工作
    variable_1 = Get_ID_18F0010B_Sig_ASR_Brake_Control_Active();
    if(variable_1 == 1)
    {
       Popup_Request(POPUT1_ASR_OPERATE);
    }
    else
    {
        Popup_Delete(POPUT1_ASR_OPERATE);
    }

    //6.PTO紧急警报-刹车
    variable_1 = Get_ID_18FED900_Sig_PTO_SW();
    variable_2 = Line_In_Get_Status(LINE_IN_PTO);//B01
    if(V_Speed &&(variable_1 || variable_2)) 
    {                                       
        Popup_Request(POPUT2_PTO);
    }
    else
    {
        Popup_Delete(POPUT2_PTO);
    }
    //7.忘记松手刹车    LINE_IN_Get_PARK_BRAKE 驻车制动
    variable_1 = Line_In_Get_Status(LINE_IN_PARK_BRAKE);//获取硬线结果
    if((V_Speed > 66)&&(variable_1 == LINE_IN_LOGIC_VALID)) //6.67Km
    {
        Popup_Request(POPUP2_PARKING_BRAKE);
    }
    else
    {
        Popup_Delete(POPUP2_PARKING_BRAKE);
    }

    //8.遥控调整车辆高度(有车速)
    variable_1 = Line_In_Get_Status(LINE_IN_AIR_SUS);//获取硬线结果
    if((V_Speed > 5)&&(variable_1 == LINE_IN_LOGIC_VALID)) //0.5Km
    {
        Popup_Request(POPUP2_AIRMATIC_HIGHT);
    }
    else
    {
        Popup_Delete(POPUP2_AIRMATIC_HIGHT);
    }

    //9.自动巡航模式
    
    variable_1 = Get_ID_18FF4100_Sig_Cruise_VariableSLD_Disp();
    if((Ign_Time > 5000)&&(variable_1 == 1))//5s内不显示
    {
       Popup_Request(POPUP3_CRUISE);
    }
    else
    {
        Popup_Delete(POPUP3_CRUISE);
    }

    //10.可变SLD 模式
    variable_1 = Get_ID_18FF4100_Sig_Cruise_VariableSLD_Disp();
    if((Ign_Time > 5000)&&(variable_1 == 3))//5s内不显示
    {
       Popup_Request(POPUP3_VARIABLE_SLD);
    }
    else
    {
        Popup_Delete(POPUP3_VARIABLE_SLD);
    }

    //11.充电异常（系统检测）
    variable_1 = Line_In_Get_Status(LINE_IN_CHARGE);
    if(EOL == 0X00)
    {   //检出A34信号（10ms周期监测）时（Lo 或 电压值＜21V连续500回以上），且EOL：LID$2B＝0ｘ00
        if((E_Speed < 350)&&(variable_1 == LINE_IN_LOGIC_VALID)) //转速350R/min
        {
            if(variable_1)
            {
                Popup_Request(POPUT4_ABNORMAL_CHARGE);
            }
            else
            {
                Popup_Delete(POPUT4_ABNORMAL_CHARGE);
            }
        }
    }
    else
    {
        Popup_Delete(POPUT4_ABNORMAL_CHARGE);
    }


    //12.油压（系统检测）
    variable_1 = Line_In_Get_Status(LINE_IN_ENG_OIL);
    if(EOL == 0X00)
    {
        if((E_Speed < 350)&&(variable_1 == LINE_IN_LOGIC_VALID)) //转速350R/min
        {
            if(variable_1)
            {
                Popup_Request(POPUP4_OIL_PRESSURE);
            }
            else
            {
                Popup_Delete(POPUP4_OIL_PRESSURE);
            }
        }
    }
    else
    {
        Popup_Delete(POPUP4_OIL_PRESSURE);
    }


    //13.AMT初始化异常           DM1 SPN4220 Key On時
    if(EOL == 0x13)
    {
        if(PowerSts == COMMON_POWER_ON)
        {
            Popup_Request(POPUP4_AMT_INIT_EXCE);
        }
        else
        {
            Popup_Delete(POPUP4_AMT_INIT_EXCE);
        }
    }
    else
    {
        Popup_Delete(POPUP4_AMT_INIT_EXCE);
    }
  

    //14.尿素品质异常（系统检测）
    //variable_1 = Get_ID_18FF2300_Sig_Amber3();
    //if(variable_1 == 1 )
    if(PowerSts == COMMON_POWER_ON)
    {
       Popup_Request(POPUP4_ADBLUE_QUALITY);
    }
    else
    {
        Popup_Delete(POPUP4_ADBLUE_QUALITY);
    }

    //15.尿素喷射异常（系统检测）
    //variable_1 = Get_ID_18FF2300_Sig_Amber1();
    //if(variable_1 == 1)
    if(PowerSts == COMMON_POWER_ON)
    {
       Popup_Request(POPUP4_ADBLUE_SPRAY);
    }
    else
    {
        Popup_Delete(POPUP4_ADBLUE_SPRAY);
    }

    //16.尿素水补给（系统检测）
    //variable_1 = Get_ID_18FF2300_Sig_Amber2();
    //if(variable_1 == 1)
    if(PowerSts == COMMON_POWER_ON)
    {
       Popup_Request(POPUP4_ADBLUE_SUPPLY);
    }
    else
    {
        Popup_Delete(POPUP4_ADBLUE_SUPPLY);
    }

    //17.AMT初始化结束               DM1 SPN4021  Key On時
    if(EOL == 0x13)
    {
        if(PowerSts == COMMON_POWER_ON)
        {
            Popup_Request(POPUP4_START_ENG);
        }
        else
        {
            Popup_Delete(POPUP4_START_ENG);
        }       
    }
    else
    {
        Popup_Delete(POPUP4_START_ENG);
    }             
 
    //18.DPD自动再生
    //variable_1 = Get_ID_18FED900_Sig_DPF_Regeneration_Status();
    if(PowerSts == COMMON_POWER_ON)
    {
        Popup_Request(POPUP4_DPD_AUTO);
    }
    else
    {
        Popup_Delete(POPUP4_DPD_AUTO);
    }


    //19.过热（过热，请在安全的场所停车）有车速     LID $43 :0x82
    //variable_1 = Get_ID_18FEEE00_Sig_Engine_Coolant_Temperature();
    if(V_Speed && (Coolant_Get_CurSeg() > 10))
    { 
        Popup_Request(POPUP5_OVER_HEAT_SPEED);
    }
    else
    {
        Popup_Delete(POPUP5_OVER_HEAT_SPEED);
    }
    //20.过热（冷却液温度过高）         无车速  LID $43 :0x82
    if((V_Speed == 0) && (Coolant_Get_CurSeg() > 10))
    {
        Popup_Request(POPUP5_OVER_HEAT);
    }
    else
    {
        Popup_Delete(POPUP5_OVER_HEAT);
    }

    //21.冷却水（冷却液不足） B32 GND
    variable_1 = Line_In_Get_Status(LINE_IN_LOW_COOLANT);
    if(V_Speed && variable_1)
    {
        Popup_Request(POPUP5_LOW_COOLANT_SPEED);
    }
    else
    {
        Popup_Delete(POPUP5_LOW_COOLANT_SPEED);
    }
    //22.冷却水（冷却水不足）B32 GND
    if((V_Speed == 0) && variable_1)
    {
        Popup_Request(POPUP5_LOW_COOLANT);
    }
    else
    {
        Popup_Delete(POPUP5_LOW_COOLANT);
    }

    //23.油压(机油)请在安全场所停车
    //发动机启动(350r/min)后、350r/min持续5秒以上时，A32信号（10ms周期监测），连续20次检出Lo时。
    variable_1 = Line_In_Get_Status(LINE_IN_ENG_OIL);
    //variable_2 = Get_ID_CF00400_Sig_Engine_speed();发动机转速 预留
    if(V_Speed && (E_Speed > 350) && variable_1)
    {
        Popup_Request(POPUP5_ENGINE_OIL_PRESSURE_SPEED);   
    }
    else
    {
        Popup_Delete(POPUP5_ENGINE_OIL_PRESSURE_SPEED);
    }
    //24.油压异常
    if((V_Speed == 0) && (E_Speed > 350) && variable_1)
    {
        Popup_Request(POPUP5_ENGINE_OIL_PRESSURE);               
    }
    else
    {
        Popup_Delete(POPUP5_ENGINE_OIL_PRESSURE);
    }
 
 
    //25.仪表故障-请在安全场所停车      //没给条件
    //26.仪表故障-请与五十铃公司联系

    //27.通信系统-请在安全场所停车      //没给条件
    //28.通信系统-请与五十铃公司联系


    //29.车速限制-图1   ID：18FF2300 Byte：7 Bit：4,3   10(B)
    variable_1 = Get_ID_18FF2300_Sig_Engine_Derate();
    if(V_Speed && (variable_1 == 2))
    {
        Popup_Request(POPUP5_SPEED_LIMIT_SPEED);           
    }
    else
    {
        Popup_Delete(POPUP5_SPEED_LIMIT_SPEED);
    }
    //30.车速限制-图2 ID：18FF2300 Byte：7 Bit：4,3   10(B)
    if((V_Speed == 0) && (variable_1 == 2))
    {
        Popup_Request(POPUP5_SPEED_LIMIT);
    }
    else
    {
        Popup_Delete(POPUP5_SPEED_LIMIT);
    }
    //31.扭矩限制-图1 ID：18FF2300 Byte：7 Bit：4,3   01(B)
    if(V_Speed && (variable_1 == 1)) 
    {
        Popup_Request(POPUP5_TORQUE_REDUCTION_SPEED);
    }
    else
    {
        Popup_Delete(POPUP5_TORQUE_REDUCTION_SPEED);
    }
    //32.扭矩限制-图2 ID：18FF2300 Byte：7 Bit：4,3   01(B)
    if((V_Speed == 0) && (variable_1 == 1))
    {
        Popup_Request(POPUP5_TORQUE_REDUCTION);
    }
    else
    {
        Popup_Delete(POPUP5_TORQUE_REDUCTION);
    }
    //33.扭矩限制、车速限制 交互 显示 ID：18FF2300 Byte：7 Bit：4,3   11(B)
    if(variable_1 == 3)
    {
        Popup_Request(POPUP5_SPEED_TORQUE);
    }
    else
    {
        Popup_Delete(POPUP5_SPEED_TORQUE);
    }


    //34.尿素品质异常-图1 ID：18FF2300 Byte：3 Bit：6,5  01(B)
    variable_1 = Get_ID_18FF2300_Sig_Amber3();
    if(V_Speed && (variable_1 ==1))
    {
        Popup_Request(POPUP5_INCORRECT_ADBLUE_SPEED);
    }
    else
    {
        Popup_Delete(POPUP5_INCORRECT_ADBLUE_SPEED);
    }
    //35.尿素品质异常-图2 ID：18FF2300 Byte：3 Bit：6,5  01(B)
    if((V_Speed == 0) && (variable_1 ==1))
    {
        Popup_Request(POPUP5_INCORRECT_ADBLUE);
    }
    else
    {
        Popup_Delete(POPUP5_INCORRECT_ADBLUE);
    }

    //36.临界排放故障-图1 ID：18FF2300 Byte：7 Bit：6,5  01(B) 
    variable_1 = Get_ID_18FF2300_Sig_EXH_System();

    if(V_Speed && (variable_1 == 1))
    {
        Popup_Request(POPUP5_CRITICAL_EMISSION_SPEED);
    }
    else
    {
        Popup_Delete(POPUP5_CRITICAL_EMISSION_SPEED);
    }

    //37.临界排放故障-图2 ID：18FF2300 Byte：7 Bit：6,5  01(B) 
    if((V_Speed == 0)&&(variable_1 == 1))
    {
    Popup_Request(POPUP5_CRITICAL_EMISSION);
    }
    else
    {
        Popup_Delete(POPUP5_CRITICAL_EMISSION);
    }


    //38.AMT异常-图1 ID：18FF8503 Byte：1 Bit：4,3 01(B) LID $41 : 0x13
    variable_1 = Get_ID_18FF8503_Sig_Spanner_Warning();         
    if((EOL == 0x13)&&(V_Speed) && (variable_1 == 1))
    {
        Popup_Request(POPUP5_AMT_SPANNER_WARNING_SPEED);
    }
    else
    {
        Popup_Delete(POPUP5_AMT_SPANNER_WARNING_SPEED);
    }

    //39.AMT异常-请重启发动机 ID：18FF8503 Byte：1 Bit：4,3 01(B) LID $41 : 0x13
    if((EOL == 0x13)&&(V_Speed == 0) && (variable_1 == 1))
    {
        Popup_Request(POPUP5_AMT_SPANNER_WARNING);
    }
    else
    {
        Popup_Delete(POPUP5_AMT_SPANNER_WARNING);
    }


    //40.AMT异常(气压低下)-图1 ID：18FF8503 Byte：2 Bit：6,5 01(B) LID $41 : 0x13
    variable_1 = Get_ID_18FF2300_Sig_Glow_Lamp();
    if((EOL == 0x13)&&(V_Speed)&&(variable_1 == 1))
    {
        Popup_Request(POPUP5_AMT_LOW_AIR_WARNING_SPEED);
    }
    else
    {
        Popup_Delete(POPUP5_AMT_LOW_AIR_WARNING_SPEED);
    }

    //41.AMT异常(气压低下)-图2
    if((EOL == 0x13)&&(V_Speed == 0)&&(variable_1 == 1))
    {
        Popup_Request(POPUP5_AMT_LOW_AIR_WARNING);
    }
    else
    {
        Popup_Delete(POPUP5_AMT_LOW_AIR_WARNING);
    }

    //42.低圧警報-轮胎漏气警告 ID：18011733  Byte：5 Bit：5 01(B) LID $3E : 0x01
    variable_1 = Get_ID_18011733_Sig_Fast_air_leakage_alarm();
    if((EOL == 0x01)&&(variable_1 == 1))
    {
       Popup_Request(POPUP5_LOW_PRESSURE_ALARM_SPEED);
    }
    else
    {
        Popup_Delete(POPUP5_LOW_PRESSURE_ALARM_SPEED);
    }
    //43.低圧警報 - 若报警图一样，同42.否则此处增加43报警逻辑

    //44.尿素补给-补充尿素溶液-图1 ID：18FF2300 Byte：3 Bit：4,3 01(B)
    variable_1 = Get_ID_18FF2300_Sig_Amber2();
    if((V_Speed)&&(variable_1 == 1))
    {
        Popup_Request(POPUP5_APP_ADBLUE_SPEED);
    }
    else
    {
        Popup_Delete(POPUP5_APP_ADBLUE_SPEED);
    }

    //45.尿素补给-补充尿素溶液-图2 ID：18FF2300 Byte：3 Bit：4,3 01(B)
    if((V_Speed == 0)&&(variable_1 == 1))
    {
        Popup_Request(POPUP5_APP_ADBLUE);
    }
    else
    {
        Popup_Delete(POPUP5_APP_ADBLUE);
    }

    //46.尿素余量少-有车速-图1 ID：18FF2300 Byte：3 Bit：4,3 10(B)
    if((V_Speed)&&(variable_1 == 2))
    {
        Popup_Request(POPUP5_ADBLUE_LEVEL_LOW_SPEED);
    }
    else
    {
        Popup_Delete(POPUP5_ADBLUE_LEVEL_LOW_SPEED);
    }

    //47.尿素余量少-无车速-图2 ID：18FF2300 Byte：3 Bit：4,3 10(B)
    if((V_Speed == 0)&&(variable_1 == 2))
    {
        Popup_Request(POPUP5_ADBLUE_LEVEL_LOW);
    }
    else
    {
        Popup_Delete(POPUP5_ADBLUE_LEVEL_LOW);
    }

    //48. 低圧警報（低下）ID：18011733  Byte：5 Bit：8 01(B) LID $3E : 0x01
    variable_1 = Get_ID_18011733_Sig_Low_Presure_Alarm();
    if((EOL == 0x01)&&(variable_1 == 1))
    {
       Popup_Request(POPUP5_LOW_FAILURE_SPEED);
    }
    else
    {
        Popup_Delete(POPUP5_LOW_FAILURE_SPEED);
    }
    //49.低圧警報（低下） 同//48


    //50.摄像头有污染-图1 ID：18FE5BE8 Byte7  Bit5-8 0010(B) 0011(B) LID $27: 0x01
    variable_1 = Get_ID_18FE5BE8_Sig_Camera_Status();
    if(V_Speed)
    {
        if((EOL == 0x01)&&(V_Speed)&&((variable_1 ==2) || (variable_2 ==3)))
        {
            Popup_Request(POPUP5_CAMERA_POLLUTION_SPEED);
        }
        else
        {
            Popup_Delete(POPUP5_CAMERA_POLLUTION_SPEED);
        }
    }
    //51.摄像头有污染-请与五十铃公司联系 ID：18FE5BE8 Byte7  Bit5-8 0010(B) 0011(B) LID $27: 0x01
    if((EOL == 0x01)&&(V_Speed == 0x00)&&((variable_1 ==2) || (variable_2 ==3)))
    {
        Popup_Request(POPUP5_CAMERA_POLLUTION);
    }
    else
    {
        Popup_Delete(POPUP5_CAMERA_POLLUTION);
    }

    //52.尿素喷射异常（停止）-图1 ID：18FF2300 Byte：3 Bit：2,1 01(B)
    variable_1 = Get_ID_18FF2300_Sig_Amber1();
    if((V_Speed)&&(variable_1 == 1))
    {
        Popup_Request(POPUP5_AdBlue_LEVEL_LOW_SPEED);
    }
    else
    {
        Popup_Delete(POPUP5_AdBlue_LEVEL_LOW_SPEED);
    }

    //53.尿素喷射异常（停止）-图2 ID：18FF2300 Byte：3 Bit：2,1 01(B)
    if((V_Speed == 0)&&(variable_1 == 1))
    {
        Popup_Request(POPUP5_AdBlue_LEVEL_LOW);
    }
    else
    {
        Popup_Delete(POPUP5_AdBlue_LEVEL_LOW);
    }

    //54.尿素喷射异常（消耗量）-图1  ID：18FF2300 Byte：3 Bit：2,1 10(B)
    if((V_Speed)&&(variable_1 == 2))
    {
        Popup_Request(POPUP5_AdBlue_INJ_SYSTEM_SPEED);
    }
    else
    {
        Popup_Delete(POPUP5_AdBlue_INJ_SYSTEM_SPEED);
    }

    //55.尿素喷射异常（消耗量）-图2 ID：18FF2300 Byte：3 Bit：2,1 10(B)
    if((V_Speed == 0)&&(variable_1 == 2))
    {
        Popup_Request(POPUP5_AdBlue_INJ_SYSTEM);
    }
    else
    {
        Popup_Delete(POPUP5_AdBlue_INJ_SYSTEM);
    }

    //56.高圧警報-轮胎高压警告 ID：18011733  Byte：5 Bit：7  01(B) LID $3E : 0x01
    variable_1 = Get_ID_18011733_Sig_High_Presure_Alarm();
    if((EOL == 0x01)&&(variable_1 == 1))
    {
        Popup_Request(POPUP5_TPMS_HIGH_AIR);
    }
    else
    {
        Popup_Delete(POPUP5_TPMS_HIGH_AIR);
    }

    //57.高温警報-轮胎高温警告 ID：18011733  Byte：5 Bit：6  01(B) LID $3E : 0x01
    variable_1 = Get_ID_18011733_Sig_High_Temperature_Alarm();
    if((EOL == 0x01)&&(variable_1  == 1))
    {
       Popup_Request(POPUP5_TPMS_HIGH_TEMP);
    }
    else
    {
        Popup_Delete(POPUP5_TPMS_HIGH_TEMP);
    }

    //58.尿素喷射异常(停止、消耗量)交互显示----尿素喷射系统异常 ID：18FF2300 Byte：3 Bit：2,1 11(B)
    variable_1 = Get_ID_18FF2300_Sig_Amber1();
    if(variable_1 == 3)
    {
        Popup_Request(POPUP5_AdBlue_DOS_MALFUNC);
    }
    else
    {
        Popup_Delete(POPUP5_AdBlue_DOS_MALFUNC);
    }

    //59.DPD手动再生要求1-DPD需要再生 18FD7C00 Byte：1 Bit：3-1  001：On – solid
    variable_1 = Get_ID_18FD7C00_Sig_DPF_Lamp_Status_Amber();

    if((V_Speed) && (variable_1 == 1))
    {
        Popup_Request(POPUP5_PUSH_DPD_SWITCH1_SPEED);
    }
    else
    {
        Popup_Delete(POPUP5_PUSH_DPD_SWITCH1_SPEED);
    }

    //60.DPD手动再生要求1-请按下DPD开关 18FD7C00 Byte：1 Bit：3-1   001：On – solid
    if((V_Speed == 0) && (variable_1 == 1))
    {
        Popup_Request(POPUP5_PUSH_DPD_SWITCH1);
    }
    else
    {
        Popup_Delete(POPUP5_PUSH_DPD_SWITCH1);
    }

    //61.DPD手动再生要求2-DPD需要再生 18FD7C00 Byte：1 Bit：3-1     100：On – fast blink (1 HZ)
    if((V_Speed) && (variable_1 == 4))
    {
        Popup_Request(POPUP5_PUSH_DPD_SWITCH2_SPEED);
    }
    else
    {
        Popup_Delete(POPUP5_PUSH_DPD_SWITCH2_SPEED);
    }

    //62.DPD手动再生要求2-请按下DPD开关 18FD7C00 Byte：1 Bit：3-1     100：On – fast blink (1 HZ)
    if((V_Speed == 0) && (variable_1 == 4))
    {
        Popup_Request(POPUP5_PUSH_DPD_SWITCH2);
    }
    else
    {
        Popup_Delete(POPUP5_PUSH_DPD_SWITCH2);
    }

    //63.TPMS故障-轮胎监控失败  ID：18011733  Byte：6 Bit：ALL 0111(B) or 1000(B) or 1001(B)
    variable_1 = Get_ID_18011733_Sig_Sensor_fault_information();
    if((variable_1 == 7) || (variable_1 == 8) ||(variable_1 == 9) )
    {
       Popup_Request(POPUP5_TPMS_FAILURE);
    }
    else
    {
        Popup_Delete(POPUP5_TPMS_FAILURE);
    }


    //64.TPMS電池低下-轮胎监控传感器电压下降  ID：18011733  Byte：5 Bit：4  01(B)  LID $3E : 0x01
    variable_1 = Get_ID_18011733_Sig_Low_Voltage_Alarm();
    if((EOL == 0x01) && (variable_1  == 1))
    {
       Popup_Request(POPUP5_TPMS_MONITOR_DROP);
    }
    else
    {
        Popup_Delete(POPUP5_TPMS_MONITOR_DROP);
    }
    //65.DPD手动再生中            //没有执行条件

    //66.遥控车辆高度调整中(无车速) B30 28V
    variable_1 = Line_In_Get_Status(LINE_IN_AIR_SUS);//获取硬线结果 B30
    if((V_Speed == 0) && (variable_1 == 1))
    {
        Popup_Request(POPUP6_HEIGHT_CONTROL);
    }
    else
    {
        Popup_Delete(POPUP6_HEIGHT_CONTROL);
    }

    //67.PTO(停车中)(无车速)
    //ID：18FED900  Byte：2 Bit：8,7  01(B)   OR  B01 28V
    variable_1 = Get_ID_18FED900_Sig_PTO_SW();
    variable_2 = Line_In_Get_Status(LINE_IN_PTO);
                                    
    if((V_Speed == 0) || (variable_1 == 1) || ( variable_2 == 1))   
    {
        Popup_Request(POPUP6_PTO_STOP);
    }
    else
    {
        Popup_Delete(POPUP6_PTO_STOP);
    }

    //68.充电异常-请在安全的场所停车
    //エンジン始動(350r/min)後、350r/minが5秒以上継続している場合、A34信号（10ms周期で監視）で。
    //发动机启动(350r/min)后、350r/min持续5秒以上时，A34信号（10ms周期监测），
    //检出（Lo 或 连续500次以上电压值＜21V）时。
    variable_1                	= Line_In_Get_Status(LINE_IN_CHARGE);                //A34
 
    if((V_Speed) && (variable_1 == 1) && (E_Speed > 350))
    {
        Popup_Request(POPUP7_CHARGE_ABNORMAL_SPEED);
    }
    else
    {
        Popup_Delete(POPUP7_CHARGE_ABNORMAL_SPEED);
    }

    //69.充电异常-请与五十铃公司联系
    if((V_Speed == 0) && (variable_1 == 1) && (E_Speed > 350))
    {
       Popup_Request(POPUP7_CHARGE_ABNORMAL);
    }
    else
    {
        Popup_Delete(POPUP7_CHARGE_ABNORMAL);
    }

    //70.AMT異常-AMT异常  ID：18FF8503　Bite：1 Bit：2,1   LID $41 : 0x13 
    variable_1 = Get_ID_18FF8503_Sig_Stop_Warning();
      
    if((EOL == 0x13) && (V_Speed) && (variable_1))
    {
        Popup_Request(POPUP7_AMT_ERROR_SPEED);
    }
    else
    {
        Popup_Delete(POPUP7_AMT_ERROR_SPEED);
    }

    //71.AMT異常-请联系经销商    
    if((EOL == 0x13) && (V_Speed == 0) && (variable_1))
    {
        Popup_Request(POPUP7_AMT_ERROR);
    }
    else
    {
        Popup_Delete(POPUP7_AMT_ERROR);
    }

    //72.补充燃料-油箱单位  LID $43 : 0x82
    //显示条件　 　：　A11的13秒平均値≧128Ω
    //不显示条件　：　A11的13秒平均値< 128Ω
    
    if((EOL == 0x82) && (Fuel_Get_Res() > 128))
    {
       Popup_Request(POPUP8_REFUEL);
    }
    else
    {
        Popup_Delete(POPUP8_REFUEL);
    }

    //73.AMT过热-离合器过载 ID：18FF8503　Bite：2 Bit：4,3  001(B)  LID $41 : 0x13
    variable_1 = Get_ID_18FF8503_Sig_Clutch_Overload_warning();
    if((EOL == 0x13) && (V_Speed) && (variable_1 == 1))
    {
        Popup_Request(POPUP8_ATM_CLUCH_OVERHEATING_SPEED);
    }
    else
    {
        Popup_Delete(POPUP8_ATM_CLUCH_OVERHEATING_SPEED);
    }

    //74.AMT过热-选择合适的档位 ID：18FF8503　Bite：2 Bit：4,3  001(B)  LID $41 : 0x13
    if((EOL == 0x13) && (V_Speed == 0) && (variable_1 == 1))
    {
        Popup_Request(POPUP8_ATM_CLUCH_OVERHEATING);
    }
    else
    {
        Popup_Delete(POPUP8_ATM_CLUCH_OVERHEATING);
    }

    //75.AMT磨耗-离合器磨损 ID：18FF8503　Bite：2 Bit：2,1  001(B)  LID $41 : 0x13
    variable_1 = Get_ID_18FF8503_Sig_Manouvering_mode();
    if((EOL == 0x13) && (variable_1 == 1))
    {
       Popup_Request(POPUP1_BRAKE_BRAKE);
    }
    else
    {
        Popup_Delete(POPUP1_BRAKE_BRAKE);
    }


    //76.低电压报警
    //显示条件：发动机启动(350r/min)后，7秒检测到23.5V时
    //显示消失条件：10秒检测到25V以上时
    if( E_Speed > 350) //转速350R/min
    {
        if( KL30_Volt < 2350)    //23.5V
        {
            Popup_Request(POPUP8_LOW_VOLTAGE_SPEED);
        }
        else if(KL30_Volt > 2500)
        {
            Popup_Delete(POPUP8_LOW_VOLTAGE_SPEED);
        }
    }
    else
    {
        Popup_Delete(POPUP8_LOW_VOLTAGE_SPEED);
    }

    //77.过电压报警
    //显示条件：发动机启动(350r/min)后，7秒检测到30.4V以上时
    //显示消失条件：10秒检测到29.4V以下时
    if( E_Speed > 350) //转速350R/min
    {
        if(KL30_Volt > 3044)    //30.44V
        {
            Popup_Request(POPUP8_OVERVOLTAGE);
        }
        else if(KL30_Volt < 2940)
        {
            Popup_Delete(POPUP8_OVERVOLTAGE);
        }
    }
    else
    {
        Popup_Delete(POPUP8_OVERVOLTAGE);
    }

    //78.DPD自动再生-DPD自动再生中  ID：18FED900 (AUXIO)  Byte：8  bit：5,4  01(B)  Engine Speed ： 350rpm以上                             
    variable_1  = Get_ID_18FED900_Sig_DPF_Regeneration_Status();

    if((V_Speed) &&(E_Speed >= 350)&&(variable_1 == 1))  
    {
        Popup_Request(POPUP8_DPD_AUTO_SPEED);               
    }
    else
    {
        Popup_Delete(POPUP8_DPD_AUTO_SPEED);
    }
    //79.DPD自动再生-再生将自动完成，不需要操作开关         
    if((V_Speed == 0) &&(E_Speed >= 350)&&(variable_1 == 1)) //转速350R/min
    {
        Popup_Request(POPUP8_DPD_AUTO);
    }
    else
    {
        Popup_Delete(POPUP8_DPD_AUTO);
    }

    
    //80.气压过低-气压过低请注意  A28 GND
    //OR条件
    //与LED等同时 任一压力传感器为539kPa(1.89V)以下时
    variable_1 = Line_In_Get_Status(LINE_IN_BRAKE_AIR_EBS); 
    if((V_Speed) && (variable_1 == 0) )
    {
        Popup_Request(POPUP9_AIR_PRESSURE_SPEED);
    }
    else
    {
        Popup_Delete(POPUP9_AIR_PRESSURE_SPEED);
    }

    //81.气压过低-请冲入空气
    if((V_Speed == 0) && (variable_1 == 0) )
    {
        Popup_Request(POPUP9_AIR_PRESSURE);
    }
    else
    {
        Popup_Delete(POPUP9_AIR_PRESSURE);
    }

    //82.EBS故障（红）-请在安全的场所停车 ID：18F0010B (EBC1)  Byte：6 Bit：3-4  01(B)  LID $21: 0x01
    variable_1 = Get_ID_18F0010B_Sig_EBS_Red_Warning_Lamp_State();
    if((EOL == 0x01) && (V_Speed ) && (variable_1 == 1)) 
    { 
        Popup_Request(POPUP9_EBS_ERROR_SPEED);
    }
    else
    {
        Popup_Delete(POPUP9_EBS_ERROR_SPEED);
    }
    //83.EBS故障（红）-请与五十铃公司联系
    if((EOL == 0x01) && (V_Speed == 0 ) && (variable_1 == 1))
    {
        Popup_Request(POPUP9_EBS_ERROR);
    }
    else
    {
        Popup_Delete(POPUP9_EBS_ERROR);
    }

    //84.省油耗建议-急加速
    //85.省油耗建议-急减速
    //86.省油耗建议-请降低发动机转速
    //87.省油耗建议-请降低速度

    //88.发动机机油＆滤清器  ID：18FF3018 Byte：1 Bit：8,7   01(B) 10(B)
    variable_1 = Get_ID_18FF3018_Sig_Engine_Oil_Warnning();
    if(variable_1 == 1 || variable_1 == 2)
    {
        Popup_Request(POPUP11_ENGINE_OIL_FILTER_ERROR);
    }
    else
    {
        Popup_Delete(POPUP11_ENGINE_OIL_FILTER_ERROR);
    }
    //89.燃油滤清器
    //依据警报阈值、前次重置时及现在的ODO值，剩余距离：1000km时，显示提前警报。
    //另外，剩余距离：负值时，再次显示本警报。

    //90.变速箱油


    //91.差速器油


    //92.顺畅系统离合器油


    //93.动力转向液


    //94.更换轮胎・轮胎位置


}



void Popups_Sound_Playing(uint8_t PopupSnd)
{
    uint8_t ReqCode = 0u;

    ReqCode = Popup_Get_Current_Sound_Req_Code( );

    switch ( PopupSnd )
    {
    /*
    case SND_RADAR                :
        if ( RADAR_SOUND == RADAR_SND_2Hz )
        {
            Sound_Delete ( SND_RADAR_4Hz );
            Sound_Delete ( SND_RADAR_CONTINUOUS );
            Sound_Request ( SND_RADAR_2Hz, ReqCode );
        }
        else if ( RADAR_SOUND == RADAR_SND_4Hz )
        {
            Sound_Delete ( SND_RADAR_2Hz );
            Sound_Delete ( SND_RADAR_CONTINUOUS );
            Sound_Request ( SND_RADAR_4Hz, ReqCode );
        }
        else if ( RADAR_SOUND == RADAR_SND_CONTINUOUS )
        {
            Sound_Delete ( SND_RADAR_2Hz );
            Sound_Delete ( SND_RADAR_4Hz );
            Sound_Request ( SND_RADAR_CONTINUOUS, ReqCode );
        }
        else
        {
            Sound_Delete ( SND_RADAR_2Hz );
            Sound_Delete ( SND_RADAR_4Hz );
            Sound_Delete ( SND_RADAR_CONTINUOUS );
        }
        break;

    case SND_FASTEN_SEATBELT      :
        if ( PopupSeatBeltDrReq == 1 )
            Sound_Request ( SND_FASTEN_SEATBELT_DR_Level_1, ReqCode );
        else if ( PopupSeatBeltDrReq == 2 )
            Sound_Request ( SND_FASTEN_SEATBELT_DR_Level_2, ReqCode );
        else if ( PopupSeatBeltDrReq == 3 )
            Sound_Request ( SND_FASTEN_SEATBELT_DR_Level_3, ReqCode );
        else
        {
            Sound_Delete ( SND_FASTEN_SEATBELT_DR_Level_1 );
            Sound_Delete ( SND_FASTEN_SEATBELT_DR_Level_2 );
            Sound_Delete ( SND_FASTEN_SEATBELT_DR_Level_3 );
        }

        if ( PopupSeatBeltPaReq == 1 )
            Sound_Request ( SND_FASTEN_SEATBELT_PA_Level_1, ReqCode );
        else if ( PopupSeatBeltPaReq == 2 )
            Sound_Request ( SND_FASTEN_SEATBELT_PA_Level_2, ReqCode );
        else if ( PopupSeatBeltPaReq == 3 )
            Sound_Request ( SND_FASTEN_SEATBELT_PA_Level_3, ReqCode );
        else
        {
            Sound_Delete ( SND_FASTEN_SEATBELT_PA_Level_1 );
            Sound_Delete ( SND_FASTEN_SEATBELT_PA_Level_2 );
            Sound_Delete ( SND_FASTEN_SEATBELT_PA_Level_3 );
        }
        break;

    case SND_DOOR_OPEN_HI_SPEED   :
    case SND_DOOR_OPEN_LOW_SPEED  :
        if ( ReqCode )
        {
            if ( WARNING_DOOR_OPEN_SND_EN == 0 )
                ReqCode = 0;
            Sound_Request ( PopupSnd, ReqCode );
        }
        else
            Sound_Delete ( PopupSnd );
        break;
    */
    default:
        if ( ReqCode )
            Sound_Request(PopupSnd, ReqCode);
        else
            Sound_Delete(PopupSnd);
        break;
    }
}