/**
  ******************************************************************************
  * @file    main.c
  * @author  MCU Application Team
  * @brief   Main program body
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; Copyright (c) 2023 Puya Semiconductor Co.
  * All rights reserved.</center></h2>
  *
  * This software component is licensed by Puya under BSD 3-Clause license,
  * the "License"; You may not use this file except in compliance with the
  * License. You may obtain a copy of the License at:
  *                        opensource.org/licenses/BSD-3-Clause
  *
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
  * All rights reserved.</center></h2>
  *
  * This software component is licensed by ST under BSD 3-Clause license,
  * the "License"; You may not use this file except in compliance with the
  * License. You may obtain a copy of the License at:
  *                        opensource.org/licenses/BSD-3-Clause
  *
  ******************************************************************************
  */

/* Includes ------------------------------------------------------------------*/
#include "main.h"
#include "py32f072xx_ll_Start_Kit.h"

/* Private define ------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private user code ---------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
static void APP_SystemClockConfig(void);
static void APP_ExtiConfig(void);
static void APP_PwrEnterStopMode(void);

/**
  * @brief  Main program.
  * @param  None
  * @retval int
  */
int main(void)
{
  /* Enable SYSCFG clock and PWR clock */
  LL_APB1_GRP2_EnableClock(LL_APB1_GRP2_PERIPH_SYSCFG);
  LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_PWR);

  /* Configure Systemclock */
  APP_SystemClockConfig();
  
  /* Initialize LED */
  BSP_LED_Init(LED_GREEN);
  
  /* Initialize Button */
  BSP_PB_Init(BUTTON_KEY,BUTTON_MODE_GPIO);

  /* Configure EXTI */
  APP_ExtiConfig();
  
  /* LED on */
  BSP_LED_On(LED_GREEN);
  
  /* Wait for the user to press the key, the program starts to run */
  while (BSP_PB_GetState(BUTTON_KEY) == 1)
  {
  }
  
  /* LED off */
  BSP_LED_Off(LED_GREEN);

  /* Enter Stop mode and wait for the PA6 pin falling edge to trigger wake up event */
  APP_PwrEnterStopMode();

  while (1)
  {
    /* LED toggle */
    BSP_LED_Toggle(LED_GREEN);
    
    /* Delay 500ms */
    LL_mDelay(500);
  }
}

/**
  * @brief  EXTI Configuration Function
  * @param  None
  * @retval None
  */
static void APP_ExtiConfig(void)
{
  /* Enable GPIOA clock */
  LL_IOP_GRP1_EnableClock(LL_IOP_GRP1_PERIPH_GPIOA);

  /* Configure PA6 as input mode */
  LL_GPIO_InitTypeDef GPIO_InitStruct = {0};
  GPIO_InitStruct.Pin = LL_GPIO_PIN_6;
  GPIO_InitStruct.Mode = LL_GPIO_MODE_INPUT;
  GPIO_InitStruct.Pull = LL_GPIO_PULL_UP;
  LL_GPIO_Init(GPIOA, &GPIO_InitStruct);

  /* Set EXTI6 to event patterns, falling edge trigger */
  LL_EXTI_InitTypeDef EXTI_InitStruct = {0};
  EXTI_InitStruct.Line = LL_EXTI_LINE_6;
  EXTI_InitStruct.LineCommand = ENABLE;
  EXTI_InitStruct.Mode = LL_EXTI_MODE_EVENT;
  EXTI_InitStruct.Trigger = LL_EXTI_TRIGGER_FALLING;
  LL_EXTI_Init(&EXTI_InitStruct);
  
  LL_EXTI_SetEXTISource(LL_EXTI_CONFIG_PORTA,LL_EXTI_CONFIG_LINE6);
}

/**
  * @brief  Enter Stop mode
  * @param  None
  * @retval None
  */
static void APP_PwrEnterStopMode(void)
{
  /* VCORE = 0.8V when enter stop mode */
  LL_PWR_SetRegulVoltageScaling(LL_PWR_REGU_VOLTAGE_0P8V);

  /* Stop mode with low-power regulator */
  LL_PWR_EnableLowPowerRunMode();

  /* Set the SLEEPDEEP bit of the Cortex system control register */
  LL_LPM_EnableDeepSleep();

  /* Request Wait Event */
  __SEV();
  __WFE();
  __WFE();

  /* Reset the SLEEPDEEP bit of the Cortex system control register */
  LL_LPM_EnableSleep();
}

/**
  * @brief  Configure system clock
  * @param  None
  * @retval None
  */
static void APP_SystemClockConfig(void)
{
  /* Enable HSI */
  LL_RCC_HSI_Enable();
  while(LL_RCC_HSI_IsReady() != 1)
  {
  }

  /* Set AHB prescaler: HCLK = SYSCLK */
  LL_RCC_SetAHBPrescaler(LL_RCC_SYSCLK_DIV_1);

  /* Select HSISYS as system clock source */
  LL_RCC_SetSysClkSource(LL_RCC_SYS_CLKSOURCE_HSISYS);
  while(LL_RCC_GetSysClkSource() != LL_RCC_SYS_CLKSOURCE_STATUS_HSISYS)
  {
  }

  /* Set APB prescaler: PCLK = HCLK */
  LL_RCC_SetAPB1Prescaler(LL_RCC_APB1_DIV_1);
  LL_Init1msTick(8000000);

  /* Update the SystemCoreClock global variable(which can be updated also through SystemCoreClockUpdate function) */
  LL_SetSystemCoreClock(8000000);
}

/**
  * @brief  Error handling function
  * @param  None
  * @retval None
  */
void APP_ErrorHandler(void)
{
  /* Infinite loop */
  while (1)
  {
  }
}

#ifdef  USE_FULL_ASSERT
/**
  * @brief  Reports the name of the source file and the source line number
  *         where the assert_param error has occurred.
  * @param  file：Pointer to the source file name
  * @param  line：assert_param error line source number
  * @retval None
  */
void assert_failed(uint8_t *file, uint32_t line)
{
  /* User can add His own implementation to report the file name and line number,
     ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
  /* Infinite loop */
  while (1)
  {
  }
}
#endif /* USE_FULL_ASSERT */

/************************ (C) COPYRIGHT Puya *****END OF FILE******************/
