/******************************************************************************
文 件 名：DoCAN_ISO15765_Config.h
功能描述：ISO 15765 规范规定的诊断服务配置文件
作 者：张暄
版 本：V1.0
日 期：2016.7.18
******************************************************************************/
/******************************************************************************
Diagnostic/Programming Specifications Applicable to the OSI Layers
===============================================================================
* NO. OSI Layer Diagnostics services
-------------------------------------------------------------------------------
7 Application ISO 14229-1 ISO 14229-3
6 Presentation -
5 Session ISO 14229-2
* 4 Transport ISO 15765-2
* 3 Network ISO 15765-2
2 Data Link ISO 11898
1 Physical ISO 11898
===============================================================================
******************************************************************************/
#ifndef _DOCAN_ISO15765_CONFIG_H_
#define _DOCAN_ISO15765_CONFIG_H_
#include "Diag_ID_Def.h"
/*-----------------------------------------------------------------------------
If CAN frame data padding is used, the DLC is always set to 8, even if the
N_PDU to be transmitted is shorter than 8 bytes. The sender has to pad any
unused bytes in the frame. In particular, this can be the case for an SF, FC
frame or the last CF of a segmented message.
-----------------------------------------------------------------------------*/
#define FILLER_BYTE_HANDLING 1u
#define FILLER_BYTE 0xCCu
/*-----------------------------------------------------------------------------
Link layer Rx FIFO depth
-----------------------------------------------------------------------------*/
#define LINK_RX_FIFO_MAX_DEPTH 8u
/*-----------------------------------------------------------------------------
Network layer buffer size
-----------------------------------------------------------------------------*/
#define N_USDATA_RX_BUFFER_SIZE 500u
#define N_USDATA_TX_BUFFER_SIZE 500u
/******************************************************************************
The FlowControl mechanism allows the receiver to inform the sender about the
receiver’s capabilities. Since different nodes may have different capabilities,
the FlowControl sent by the receiver informs the sender about its capabilities.
The sender shall conform to the receiver’s capabilities.
These capabilities are defined as follows.
******************************************************************************/
/*-----------------------------------------------------------------------------
— BlockSize (BS): The maximum number of N_PDUs the receiver allows the sender
to send, before waiting for an authorization to continue transmission of the
following N_PDUs.
-----------------------------------------------------------------------------*/
#define N_MAX_BS 8u
/*-----------------------------------------------------------------------------
— SeparationTime minimum (STmin): The minimum time the sender is to wait
between transmission of two CF N_PDUs. (Unit: ms)
-----------------------------------------------------------------------------*/
#define N_STmin 0x14u
/*-----------------------------------------------------------------------------
— N_WFTmax: Upper limit to the number of FC.WAIT a receiver is allowed to send
in a row. This parameter is a system design constant and is not
transmitted in the first FC N_PDU.
-----------------------------------------------------------------------------*/
#define N_WFTmax 0u
/******************************************************************************
Timing parameters
******************************************************************************/
/*-----------------------------------------------------------------------------
- Timing Parametera : N_As
- Description : Time for transmission of the CAN frame (any N_PDU)
on the sender side
- Start : L_Data.request
- End : L_Data.confirm
- Timeout(Max) : 1,000 ms
- Performance Requirement :
-----------------------------------------------------------------------------*/
#define N_As ((uint32_t)25)
/*-----------------------------------------------------------------------------
- Timing Parametera : N_Ar
- Description : Time for transmission of the CAN frame (any N_PDU)
on the receiver side
- Start : L_Data.request
- End : L_Data.confirm
- Timeout(Max) : 1,000 ms
- Performance Requirement :
-----------------------------------------------------------------------------*/
#define N_Ar ((uint32_t)25)
/*-----------------------------------------------------------------------------
- Timing Parametera : N_Bs
- Description : Time until reception of the next FlowControl N_PDU
- Start : L_Data.confirm (FF) / L_Data.confirm (CF) /
L_Data.indication (FC)
- End : L_Data.indication (FC)
- Timeout(Max) : 1,000 ms
- Performance Requirement :
-----------------------------------------------------------------------------*/
#define N_Bs ((uint32_t)75)
/*-----------------------------------------------------------------------------
- Timing Parametera : N_Br
- Description : Time until transmission of the next FlowControl
N_PDU
- Start : L_Data.indication (FF) / L_Data.indication (CF)
L_Data.confirm (FC)
- End : L_Data.request (FC)
- Timeout(Max) : N/A
- Performance Requirement : (N_Br + N_Ar) < (0.9 × N_Bs timeout)
-----------------------------------------------------------------------------*/
#define N_Br ((uint32_t)9)
/*-----------------------------------------------------------------------------
- Timing Parametera : N_Cs
- Description : Time until transmission of the next
ConsecutiveFrame N_PDU
- Start : L_Data.indication (FC) / L_Data.confirm (CF)
- End : L_Data.request (CF)
- Timeout(Max) : N/A
- Performance Requirement : (N_Cs + N_As) < (0.9 × N_Cr timeout)
-----------------------------------------------------------------------------*/
#define N_Cs ((uint32_t)0)
/*-----------------------------------------------------------------------------
- Timing Parametera : N_Cr
- Description : Time until reception of the next Consecutive Frame
N_PDU
- Start : L_Data.confirm (FC) / L_Data.indication (CF)
- End : L_Data.indication (CF)
- Timeout(Max) : 1,000 ms
- Performance Requirement :
-----------------------------------------------------------------------------*/
#define N_Cr ((uint32_t)150)
/******************************************************************************
For debug purpose
******************************************************************************/
/*-----------------------------------------------------------------------------
Global debug switch
-----------------------------------------------------------------------------*/
#define DOCAN_DEBUG_EN (uint8_t) 0
/*-----------------------------------------------------------------------------
Bug indicator functions
-----------------------------------------------------------------------------*/
#endif